Bud Lightyear (20-08-17), GEORGE (11-12-18), M_C (21-08-17)
Well done mukka..
Regards BL
Lightyear's Amnesia Adventure
Lightyear's Jingle All The Way
Lightyear's Exodus Extravaganza
Lightyear's If You Like Cheese
Lightyear's To Infinity
Lightyear's Twin Quad 50 Oz Cheese 2kw
Lightyear's 55 Oz Christmas Cracker
Lightyears Guide To Cuttings
Super Silent Ruck 200L
Lightyears Guide To Uploading Photos
How To Build A Twin Variac With Fan Speed Controller
Member Of The Month Leader board
GEORGE (11-12-18), Jesse Pinkman (21-08-17), kush king (25-03-18), M_C (21-08-17)
Bud Lightyear (21-08-17), Danj246 (21-08-17), GEORGE (11-12-18), M_C (21-08-17)
Pity you lost your pics mate but luckily i was able to build this system from your tops vid.
Bud Lightyear (21-08-17), GEORGE (11-12-18), Jesse Pinkman (21-08-17), M_C (21-08-17)
Nice to see the pics back, helped no end with my build
Bud Lightyear (21-08-17), Jesse Pinkman (21-08-17)
Awesome thanks for taking time to repost pics
Sent from my SM-G935F using Tapatalk
Bud Lightyear (21-08-17), GEORGE (11-12-18), Jesse Pinkman (21-08-17)
What do you use to make the holes in the box lids for the net pots to sit in? I always seem to make an arse of it tryna cut the hole out
Sent from my SM-G935F using Tapatalk
GEORGE (11-12-18)
I have been looking for a system to suit my needs and you just inspired me to start my own project. Thanks amigo
Sent from my SM-G950F using Tapatalk
GEORGE (11-12-18)
might be a bit late to reply, but can be useful for anyone else building a system.
I use a piece of wood with 2 screws in it.
I find the centre of the box lid by drawing 2 diagonal lines from the corners.
then measure your netpot diameter at the top.
Say its exactly 200mm for example.
Drill a small pilot hole in the centre of the box.
Then get a length of timber, say 2*1 inch. Drill a pilot hole about 30mm from the end in the centre of the wood, then another a further 90mm onward from this hole.
Screww a screw thru the pilot holes in the wood till it poking thru the other side about 5mm.
Now measure the distance between the 2 screws, should be about 90mm.
Now place the point of the screw into the lids pilot hole, and slowly start turning the wood in a circular motion. This will scribe a perfect circle 180mm in diameter. Now just keep turning till you eventually go thru the lids plastic (clue, don't do this on your best wooden floor )
Now your net pot will fit into the hole, and you will have zero chance of it falling thru the hole.
Because I'm lazy I used to just make the hole the same diameter as the inside diameter of the netpot, but either way works.
Hopefully this is understandable.
You can also use a jigsaw, but ive cracked too many lids using these things, so just use my trusty timber and 2 screws.
GEORGE (11-12-18)
wooohooooo! very handy procedure! loving the final buildup
GEORGE (11-12-18)
THCtalk.com Disclaimer - You must be over 18 years old to view/use this site .THCtalk.com does not encourage growing Cannabis or possessing Cannabis. Learning how to grow Cannabis instructions should be for educational purposes only. All Information contained in this web site is for: Historical reference, Scientific reference and Educational purposes only. Visitors to this website are advised against breaking the law as It is illegal to smoke, grow, or possess cannabis in the UK and some US States
Bookmarks