Page 2 of 2 FirstFirst 1 2
Results 21 to 25 of 25

Thread: Mk2 grow box

  1. #21

    Join Date
    Apr 2017
    Posts
    519
    Thanks
    261
    Thanked 876 Times in 453 Posts

    Default

    Quote Originally Posted by gardro View Post
    Bluelab do one but you could undercut them for sure
    Aye its like what 1k for the controller then about 900 for the actual drippers lol


    Sent from my iPhone using Tapatalk

  2. The Following 3 Users Say Thank You to Done420 For This Useful Post:

    gardro (07-09-18), HisHighness (09-09-18), hotshot (07-09-18)

  3. #22

    Join Date
    Mar 2018
    Posts
    236
    Thanks
    217
    Thanked 541 Times in 225 Posts

    Default

    Quote Originally Posted by gardro View Post
    Bluelab do one but you could undercut them for sure
    Yeh man, biggest cost is the stepper motors. All in a few hundred would cover an 8 channel example for all the parts.

    That should be enough for:

    Liquid silicon,
    Ph down,
    Grow,
    Bloom,
    Micro,
    2x different Flower boosters

    I'm in the middle of designing a load of parts, ducts, valves, brackets etc. Progress has been slow!

    Sent from my SM-G960F using Tapatalk

  4. The Following 5 Users Say Thank You to HisHighness For This Useful Post:

    British green (09-09-18), Done420 (09-09-18), gardro (09-09-18), Gaz (09-09-18), hotshot (09-09-18)

  5. #23

    Join Date
    Mar 2018
    Posts
    236
    Thanks
    217
    Thanked 541 Times in 225 Posts

    Default

    Some pics of the 3d work I've been doing.

    Case for the led drivers, and prototype of the ducting valve. Two of these will allow a recirculating system or normal intake -> exhaust.

    The bottom section housing all the mechanics and power will have a good deal of heat, which can be used to warm the air above if needed.

    Having it recirculating will also make it much more efficient to cool and maintain humidity...



    Sent from my SM-G960F using Tapatalk

  6. The Following 4 Users Say Thank You to HisHighness For This Useful Post:

    Done420 (10-09-18), gardro (13-09-18), hotshot (10-09-18), WhIpLaSh (13-09-18)

  7. #24

    Join Date
    Mar 2018
    Posts
    236
    Thanks
    217
    Thanked 541 Times in 225 Posts

    Default

    Still designing ducting, but hooked up some code to the flap controller
    giggidy.



    Sent from my SM-G960F using Tapatalk

  8. The Following 5 Users Say Thank You to HisHighness For This Useful Post:

    British green (15-09-18), Done420 (13-09-18), gardro (13-09-18), hotshot (14-09-18), WhIpLaSh (13-09-18)

  9. #25

    Join Date
    Mar 2018
    Posts
    236
    Thanks
    217
    Thanked 541 Times in 225 Posts

    Default

    Looking at the layout of some of the LEDs... 3000k and 4000k and the far red LEDs...

    Where would you put them?

    I got 2 50w full spectrum cobs on the way too.. thinking they can go between the far red in the centre...

    Sent from my SM-G960F using Tapatalk

  10. The Following 2 Users Say Thank You to HisHighness For This Useful Post:

    gardro (14-09-18), hotshot (14-09-18)

Page 2 of 2 FirstFirst 1 2

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Quebec Cannabis Seeds

Bonza Seeds - Over 2000 Strains!     |     bongs - herbtools     |     25% off Cannabis Seeds at Dr Chronic     |     buy a bong from Herb Tools     |     GYO Seedbank     |     Buy Cannabis Seeds     |     www.alibongocannabisseeds.co.uk

THCtalk.com Disclaimer - You must be over 18 years old to view/use this site .THCtalk.com does not encourage growing Cannabis or possessing Cannabis. Learning how to grow Cannabis instructions should be for educational purposes only. All Information contained in this web site is for: Historical reference, Scientific reference and Educational purposes only. Visitors to this website are advised against breaking the law as It is illegal to smoke, grow, or possess cannabis in the UK