Before and after shots. Just managed to fit the filter into the box
Current grow mentored by MrChedHead:
https://www.thctalk.com/cannabis-foru...post1070864098
Bespoke diy light build mentored by Gadro:
https://www.thctalk.com/cannabis-foru...tored-by-Gardo
Agent Green (23-10-19), Cleargreen (06-01-19), gardro (06-01-19), GasMan (06-01-19), Gaz (06-01-19), GEORGE (22-10-19), WhIpLaSh (06-01-19)
Cracking job Silk mate gonna see good things.happening under that light mate for sure
Great job Lads good thread
Sour Livers - mentored by BB
https://www.thctalk.com/cannabis-for...-mentored-grow
Gaz builds the Igloo
https://www.thctalk.com/cannabis-for...ilds-an-igloo-)
Cleargreen (06-01-19), gardro (06-01-19), GEORGE (22-10-19), Silkadin (06-01-19)
Looks sweeeeet, Silk! Great job matey
Top build bro.! I followed along with excitement. !!
Sent from my iPhone using Tapatalk
Toms Iws Flood & drain system using coco. 2020.
https://www.thctalk.com/cannabis-for...ems-using-Coco
Cleargreen (06-01-19), gardro (06-01-19), GEORGE (22-10-19), Silkadin (23-10-19)
Check how deep the light is penetrating now. Plants going to love you
Current diary
https://www.thctalk.com/cannabis-foru...le-Sun-Led-Kit
Amazing job you did there!
I hate to say it... but I may be altering this light at some point as I'm hoping to build a taller grow area... however I want it about 45 to 50cm deep max and this light is about 58cm deep, and 70 wide (when you include the driver and dimmer switch). I'm hoping the new cabinet will measure about 145cm tall with a growing area of 75cm width, 45cm depth and 110cm height. The remaining 35cm height will be allocated below the grow area and will house the fan and cf... that boxed area will be extracted into but will have a vent from in through the wall to outside (since the vents already in place). So I'll have 20cm more height which will be nice, but it means either removing or somehow relocating two of the strips. Waiting will drop by 30 but that's ok by me and will only help keep down the leccy Bill's. The other challenge will be making a light proof door for these retina nuking light strips
CityDweller (22-10-19), Cleargreen (22-10-19), gardro (22-10-19), GEORGE (22-10-19), thelastrebel (22-10-19)
Part of the beauty of strip builds mate is they're so easily reconfigureable. You may have to rotate 90°, depending on which side is the long side, but measure up and drill some new holes and you should be able to move the strips close enough together that it'll fit pretty comfortably - and if the driver's taking up too much room you could move it as long as you have a long enough DC cable. Peobably better to have more strips closer together rather than removing some as you'll have more power available if you want it and it should be a touch more efficient to produce the same amount of light by dimming rather than removing.
Cleargreen (22-10-19), gardro (23-10-19), GEORGE (22-10-19), Silkadin (23-10-19)
Go for it Silk, that is one of the big advantages of a self build light made up of multiple strips, you can add to or remove strips as needed. Good luck trying that with an IS panel
THCtalk.com Disclaimer - You must be over 18 years old to view/use this site .THCtalk.com does not encourage growing Cannabis or possessing Cannabis. Learning how to grow Cannabis instructions should be for educational purposes only. All Information contained in this web site is for: Historical reference, Scientific reference and Educational purposes only. Visitors to this website are advised against breaking the law as It is illegal to smoke, grow, or possess cannabis in the UK and some US States
Bookmarks