Results 1 to 2 of 2

Thread: thc extraction

  1. #1

    Join Date
    Jun 2008
    Location
    The ultimate grow room
    Posts
    237
    Thanks
    0
    Been Thanked: 6 Times

    Default thc extraction

    ************************************************** ***************************
    THC-Resin Extraction
    ************************************************** ***************************
    Since so much time, labour, and cost has gone into the production of each plant, growers do not
    overlook utilization of the "shake" or leaves. Extraction involves the process of removing the essential
    oil, THC resin, from the leaves remaining on the plant and those removed during pruning. This is
    accomplished through the use of a solvent in which the oil will dissolve, which is later separated from the
    plant material by passing it through an appropriate filter. The best solvent found to date is chloroform. It
    is non-flammable, which makes it safer to handle than ethanol. Further, it has a low boiling point (61 C.,
    142 F.), and a residue after evaporation of .0005 percent. This low residue percentage means that
    virtually no trace solvent remains to contaminate the oil and cause an aftertaste, which is usually a
    problem encountered with ethanol unless time-consuming distillation processes are used. Another
    important concern is that chlorophyll is relatively insoluble in chloroform, eliminating the heavy "green"
    taste that always results from ethanol extractions. To initiate the extraction process, the leaves must be
    dried thoroughly. This can be done by placing them on fairly absorbent paper, such as newsprint, in a
    good sunny spot near a window. (Fresh newsprint paper can be obtained in most art supply stores.
    The lead content of ordinary newspapers makes them unsuitable for this purpose.) The leaves are then
    turned over every few days to ensure complete drying. When they are sufficiently and completely dried,
    the leaves should be brittle and crumble easily between the fingers. They are then placed in a blender or
    food processor and ground to a fine powder. Studies have shown that to achieve 90 percent extraction
    of the oil, the plant material must be powdered. ["Studies"?! Don't ask... -ed.] This is because nearly
    as much oil is contained in non-glandular internal tissues as is produced by the glandular tri-chomes.
    Next, a filter (a coffee filter will do) is placed over a clean Pyrex beaker or Corning Ware dish. The
    plant material is piled about halfway to the top of the filter, and the rest of the material (if any) is saved in
    an air-tight container. Pour approximately 200 ml of chloroform into the blender or food processor and
    slosh it around the sides. This rinses out any oil that may have adhered to the container's walls.
    Chloroform is poured from the blending container over the plant material until it reaches the top of the
    filter (adding more chloroform if needed). When the chloroform has completely filtered in to the beaker
    or dish, this process is repeated by adding chloroform until it again reaches the top of the filter. Two
    extractions of the same plant material are usually sufficient to remove all of its THC oil. The plant
    material is discarded; the same procedure is repeated until the beaker or dish becomes full of solvent.
    Now the beaker or dish is placed on an electric stove or hot plate and heated slowly to a very low boil.
    When the chloroform is being evaporated, the area must be completely ventilated! In the early days of
    medicine, chloroform was used as an anaesthetic until harmful side effects [such as liver damage! -ed.]
    were discovered, so it is clear that extreme care must be used when evaporating this solvent. After the
    solvent has been evaporated, the same procedure is repeated until all of the plant material has been
    treated. The oil is collected and stored in a glass pipette. These can be obtained at a scientific supply
    and are inexpensive. The oil is drawn into the tube (this may be easier if the oil is first heated a bit), and
    the tube capped at both ends. Resin is best stored inside airtight containers and in an area of low light
    and humidity.



  2. #2

    Join Date
    Jul 2009
    Location
    Inside of a bud plant.
    Posts
    184
    Thanks
    0
    Been Thanked: 2 Times

    Question Oil from Male Plants??

    Great read... can you do this with a male plant?

    I mean you can, but is there enough of THC that is worth concentrating for a decent high-inducing oil???

    Reason I ask is I have some fairly large male plants I chopped, but I would hate to just chop 'em up and throw them in the compost. Feels like I should do more.

    Thanks for that SO.

Similar Threads

  1. Extraction?
    By JAFQ in forum Grow Room Design and Setups
    Replies: 11
    Last Post: 06-07-23, 07:54 PM
  2. help with extraction plz
    By meangreenmachine in forum Indoor Cannabis Growing
    Replies: 6
    Last Post: 25-01-10, 06:20 PM
  3. Which Extraction
    By where dem tings in forum Grow Room Design and Setups
    Replies: 1
    Last Post: 24-11-09, 04:10 PM
  4. What extraction?
    By -Smokey- in forum Grow Room Design and Setups
    Replies: 19
    Last Post: 19-10-09, 10:02 AM
  5. extraction help
    By -Smokey- in forum Grow Room Design and Setups
    Replies: 3
    Last Post: 19-06-09, 11:27 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  


THCtalk.com Disclaimer - You must be over 18 years old to view/use this site .THCtalk.com does not encourage growing Cannabis or possessing Cannabis. Learning how to grow Cannabis instructions should be for educational purposes only. All Information contained in this web site is for: Historical reference, Scientific reference and Educational purposes only. Visitors to this website are advised against breaking the law as It is illegal to smoke, grow, or possess cannabis in the UK and some US States