British green (02-01-17), Bud Lightyear (05-01-17), Glynne (05-01-17)
Must know I thing or two that bud Lightyear guy lol . All credit is his
sent from mission control
Bud Lightyear (05-01-17), Glynne (05-01-17)
British green (03-01-17), Bud Lightyear (05-01-17), Glynne (05-01-17), joker_the_smoker (03-01-17)
Had an eye on them my self, thay do on for rh to,
One hooked up to an ac and heater, and one hooked to and humid and demi...perfic vpd ea m8,,recon if you hooked one to a thermoelectric chip you could make a flash cooler for the feed line on a nft systum or something,..really good bito kit for the cost, to you sir
Mon the sticky
Just chillin in ma long johns reading about plants. And it's ten plants max man. Don't be an idiot new guy .
Bud Lightyear (05-01-17), Glynne (05-01-17)
So I'm confused at this. I'm using a 1 gang socket and the temp item.
I want to just control my heater. What am I wiring up? My heater has a plug which will go into the socket.
Which part of the elitech actually controls the on/off function?
And if I set it just on the heat section would this work? So it clicks heater on below 20 degrees and I want it turned off at 24.
Thanks.
GRAND DADDY PURPS X BIG BUD HYDRO DIARY https://www.thctalk.com/cannabis-foru...d.php?t=151524
Bud Lightyear (13-01-17)
Crude but is this roughly what I'm looking at?
British green (06-01-17), Bud Lightyear (13-01-17)
I can't see the colors of your wires fwank but . The supply is your incoming power so on the end of that you want your three pin plug . The two screws that are directly under the drawing of the open gate ( switch ) saying heating will control your heater . This will be wired to a single socket to accept tour heater plug . Hope that helps . Please be careful and check back if your unsure
sent from mission control
Bud Lightyear (13-01-17)
Will the live wire work plugged into a 1 gang?
I have live brown wire into the elitech power on and heater controller then out to the plug socket.
I have neutral blue going to controller power and plug socket
I have ground/earth going to plug socket.
So brown is going into power the controller which is then going to the relay for triggering the heater which is then going into the plug socket.
You struggling to see the wires in the picture that aren't coloured in?
Red equals Brown in that picture.
Last edited by Fwank; 06-01-17 at 12:38 AM.
Bud Lightyear (13-01-17)
That picture looks correct I can see red
sent from mission control
Bud Lightyear (13-01-17), Fwank (06-01-17), locky_7 (06-01-17)
Thanks didn't want to get it wrong just need to set up the hole for the 1 gang tonight as I'm guessing I'm going to have to drill a hole in the middle for the wires then screw it in via holes.
My heater warms it up too quick had it on for 1 hour on minimum and it reached 30 degrees with fan on full and the floor fan on.
Typical!
British green (06-01-17), Bud Lightyear (13-01-17)
THCtalk.com Disclaimer - You must be over 18 years old to view/use this site .THCtalk.com does not encourage growing Cannabis or possessing Cannabis. Learning how to grow Cannabis instructions should be for educational purposes only. All Information contained in this web site is for: Historical reference, Scientific reference and Educational purposes only. Visitors to this website are advised against breaking the law as It is illegal to smoke, grow, or possess cannabis in the UK and some US States
Bookmarks